{"id":425235,"date":"2024-10-20T06:55:45","date_gmt":"2024-10-20T06:55:45","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-iso-218052023\/"},"modified":"2024-10-26T13:03:32","modified_gmt":"2024-10-26T13:03:32","slug":"bs-en-iso-218052023","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-iso-218052023\/","title":{"rendered":"BS EN ISO 21805:2023"},"content":{"rendered":"
This document gives guidelines for fulfilling the requirements contained in ISO 6183:2022, 6.4.1 and 7.4.1 and ISO 14520?1:2023, 5.2.1 h) and 5.3 h), in respect to over- and under-pressurization venting and post-discharge extract. It considers the design, selection and installation of vents to safeguard the structural integrity of enclosures protected by fixed gaseous extinguishing systems and the post-discharge venting provisions where used.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
4<\/td>\n | European foreword Endorsement notice <\/td>\n<\/tr>\n | ||||||
6<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | 4 Symbols and abbreviated terms <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 5 Use and limitations <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 6 Safety 6.1 Structural safety 6.2 Personnel safety 7 System design \u2014 Pressure-relief venting 7.1 General <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 7.2 Extinguishant characteristics 7.2.1 Positive and negative pressurization 7.2.2 Pressure graphs <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 7.3 Enclosure characteristics 7.4 Pressure-relief vent paths <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 7.5 Types of pressure-relief vents 7.5.1 General 7.5.2 Gravity vents 7.5.3 Counterweighted flap vent <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 7.5.4 Electrically-operated vents 7.5.5 Pneumatically-operated vent 7.5.6 Vent accessories <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 7.6 Pressure-relief vent characteristics 7.6.1 Vent efficiency <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | 7.6.2 Minimum opening pressure 7.6.3 Minimum closing pressure 7.6.4 Fire rating 7.7 Vent location and mounting 7.7.1 Vent location <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 7.7.2 Vent mounting <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | 7.8 Pressure-relief vent area calculations 7.8.1 Use of agent-specific formulae <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | 7.8.2 Vent area requirement (non-liquefiable gases) <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | 7.8.3 Vent area requirement carbon dioxide 7.8.4 Vent area requirements (liquefiable gases) <\/td>\n<\/tr>\n | ||||||
30<\/td>\n | 7.8.5 Leakage 7.9 Cascade venting calculations <\/td>\n<\/tr>\n | ||||||
31<\/td>\n | 7.9.1 Example calculation 3: Cascade venting calculations for IG-541 (peak discharge) <\/td>\n<\/tr>\n | ||||||
32<\/td>\n | 7.9.2 Cascade vent arrangements <\/td>\n<\/tr>\n | ||||||
33<\/td>\n | 7.9.3 Venting into adjacent enclosures <\/td>\n<\/tr>\n | ||||||
35<\/td>\n | 8 System design \u2014 Post-discharge venting 9 Acceptance 10 Service and maintenance <\/td>\n<\/tr>\n | ||||||
37<\/td>\n | Annex A (informative) Development of agent-specific formulae for liquefiable gases <\/td>\n<\/tr>\n | ||||||
42<\/td>\n | Annex B (informative) Method for development of agent-specific formulae for liquefiable gases <\/td>\n<\/tr>\n | ||||||
44<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Guidance and recommendations on design, selection and installation of vents to safeguard the structural integrity of enclosures protected by gaseous fire-extinguishing systems<\/b><\/p>\n |