B30.7 includes provisions that apply to the construction, installation, operation, inspection, testing and maintenance of winches arranged for mounting on a foundation or other supporting structure for moving loads. Winches addressed in this volume are those typically used in industrial, construction and maritime applications. The requirements included in this volume apply to winches that are powered by internal combustion engines, electric motors, compressed air or hydraulics and that utilize drums and rope. This volume does not apply to overhead hoists, mine hoists, capstans or winches installed as an integral part of the lifting system of other B30 equipment.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | CONTENTS Figures |
| 5 | FOREWORD |
| 7 | ASME B30 COMMITTEE ROSTER |
| 9 | B30 STANDARD INTRODUCTION SECTION I: SCOPE SECTION II: SCOPE EXCLUSIONS SECTION III: PURPOSE SECTION IV: USE BY REGULATORY AGENCIES SECTION V: EFFECTIVE DATE |
| 10 | SECTION VI: REQUIREMENTS AND RECOMMENDATIONS SECTION VII: USE OF MEASUREMENT UNITS SECTION VIII: REQUESTS FOR REVISION SECTION IX: REQUESTS FOR INTERPRETATION SECTION X: ADDITIONAL GUIDANCE |
| 12 | SUMMARY OF CHANGES |
| 14 | Chapter 7-0 Scope, Definitions, Personnel Competence, and References SECTION 7-0.1: SCOPE OF B30.7 SECTION 7-0.2: DEFINITIONS |
| 15 | SECTION 7-0.3: PERSONNEL COMPETENCE SECTION 7-0.4: REFERENCES TO OTHER CODES AND STANDARDS |
| 16 | Fig. 7-0.2-1 Winch With Capstan Fig. 7-0.2-2 Single-Drum Winch Fig. 7-0.2-3 Three-Drum Winch With Attached Swinger |
| 17 | Fig. 7-0.2-4 Independent Direct Geared Swinger or Single-Drum Winch |
| 18 | Chapter 7-1 Construction and Installation SECTION 7-1.1: RATINGS AND MARKINGS 7-1.1.1 Basis 7-1.1.2 Winch Ratings 7-1.1.3 Markings 7-1.1.4 Rope Layer Ratings SECTION 7-1.2: CONSTRUCTION 7-1.2.1 General 7-1.2.2 Winch Mechanisms 7-1.2.3 Brakes 7-1.2.4 Guards 7-1.2.5 Ropes |
| 19 | 7-1.2.6 Winch Controls 7-1.2.7 Control Forces and Movements 7-1.2.8 Engine Clutch 7-1.2.9 Jaw Clutch 7-1.2.10 Electric Resistors 7-1.2.11 Switches 7-1.2.12 Lubrication SECTION 7-1.3: INSTALLATION 7-1.3.1 Attachments and Anchorages 7-1.3.2 Installation Location of Winches |
| 20 | Chapter 7-2 Inspection, Testing, and Maintenance SECTION 7-2.1: INSPECTION 7-2.1.1 General 7-2.1.2 Initial Inspection and Test 7-2.1.3 Daily Inspection and Test 7-2.1.4 Frequent Inspection |
| 21 | 7-2.1.5 Periodic Inspection 7-2.1.6 Winches Not in Regular Service SECTION 7-2.2: TESTING 7-2.2.1 Operational Tests 7-2.2.2 Load Test |
| 22 | SECTION 7-2.3: MAINTENANCE 7-2.3.1 Preventive Maintenance 7-2.3.2 Maintenance Procedure 7-2.3.3 Adjustments and Repairs 7-2.3.4 Lubrication SECTION 7-2.4: ROPE INSPECTION, REPLACEMENT, AND MAINTENANCE 7-2.4.1 General 7-2.4.2 Rope Inspection 7-2.4.3 Rope Replacement |
| 23 | 7-2.4.4 Rope Maintenance |
| 24 | Chapter 7-3 Operations SECTION 7-3.1: QUALIFICATIONS AND CONDUCT OF OPERATORS 7-3.1.1 Operators 7-3.1.2 Qualifications for Operators 7-3.1.3 Responsibilities |
| 25 | 7-3.1.3.1 Responsibilities of the Equipment Owner and User. 7-3.1.3.1.1 7-3.1.3.1.2 7-3.1.3.2 Responsibilities of Site Supervisor and Lift Director. 7-3.1.3.2.1 |
| 26 | 7-3.1.3.2.2 7-3.1.3.3 Responsibilities of Equipment Operators. |
| 27 | 7-3.1.3.4 Rigger’s Responsibilities. 7-3.1.4 Cautions to Personnel SECTION 7-3.2: OPERATING PRACTICES 7-3.2.1 Winch Selection 7-3.2.2 Size of Load 7-3.2.3 Moving the Load |
| 28 | 7-3.2.4 Holding the Load 7-3.2.5 Use of a Capstan Drum 7-3.2.6 Storage SECTION 7-3.3: MISCELLANEOUS 7-3.3.1 Fire Extinguisher 7-3.3.2 Refueling SECTION 7-3.4: COMMUNICATIONS 7-3.4.1 General 7-3.4.2 Standard Signals |
| 29 | 7-3.4.3 Signalperson Qualifications 7-3.4.4 Standard Hand Signals 7-3.4.5 Standard Voice Signals 7-3.4.6 Special Signals |
| 30 | Fig. 7-3.4.4-1 Standard Hand Signals for Controlling Winch Operations |
Related products
-
ASME HST 4 2016
ASME HST-4 – 2016: Performance Standard for Overhead Electric Wire Rope Hoists Published By Publication…
