ASTM-A480 2005

$58.50

A480/A480M-05 Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip

Published By	Publication Date	Number of Pages
ASTM	2005	24

Guaranteed Safe Checkout

Categories: 77.140.50 - Flat steel products and semi-products, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 This specification covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued by ASTM: Specifications A167, A176, A240/A240M, A263, A264, A265, A666, A693, A793, and A895.

1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.

1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets, except that when A480M is specified, Annex A3 shall apply for the dimensional tolerances and not the bracketed SI values in Annex A2. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.4 This specification and the applicable material specifications are expressed in both inch-pound and SI units. However, unless the order specifies the applicable ‘M’ specification designation (SI units), the material shall be furnished in inch-pound units.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents
2	Terminology Ordering Information Process Heat Analysis
3	Product Analysis Material Test Report and Certification Permitted Variations in Dimensions and Weight Workmanship
4	Finish for Sheet Finish for Strip Finish for Plates
5	Edges for Cold-Rolled Strip Heat Treatment Number of Tests Test Specimens
6	Special Tests
7	Test Methods Retests and Retreatment Repair of Plate by Welding Inspection Rejection Rehearing
8	Packaging, Marking, and Loading Keywords A1. PRODUCT ANALYSIS TOLERANCES AND HEAT TREATMENT REQUIREMENTS A1.1
9	TABLE A1.1
10	A2. PERMITTED VARIATIONS IN DIMENSIONS, ETC.—INCH-POUND UNITS A2.1 A2.2 Cold-Rolled Narrow (<24 in. [610 mm] width) Coil-Processed Product A2.3 Cold-Rolled Wide (24 in. [610 mm] width) Coil-Processed Product A2.4 Hot-Rolled Narrow (<24 in. [610 mm] width) Coil-Processed Product A2.5 Hot-Rolled Wide (24 in. [610 mm] width) Coil-Processed Product A2.6 Hot-Rolled Product Processed Without Coiling TABLE A1.2
11	A2.7 Cold-Rolled Product Processed Without Coiling A2.8 Tolerances for other dimensional characteristics TABLE A2.1 TABLE A2.2 TABLE A2.3 TABLE A2.4
12	TABLE A2.5 TABLE A2.6 TABLE A2.7
13	TABLE A2.8 TABLE A2.9 TABLE A2.10 TABLE A2.11 TABLE A2.12
14	TABLE A2.13 TABLE A2.14 TABLE A2.15 TABLE A2.16
15	TABLE A2.17 TABLE A2.18 TABLE A2.19 TABLE A2.20
16	TABLE A2.21 TABLE A2.22 TABLE A2.23 TABLE A2.24 TABLE A2.25
17	TABLE A2.26 TABLE A2.27 TABLE A2.28 TABLE A2.29
18	A3. PERMITTED VARIATIONS IN DIMENSIONS, ETC.—SI UNITS A3.1 A3.2 Cold-Rolled Narrow (<600 mm width) Coil-Processed Product A3.3 Cold-Rolled Wide (600 mm width) Coil-Processed Product A3.4 Hot-Rolled Narrow (<600 mm width) Coil-Processed Product A3.5 Hot-Rolled Wide (600 mm width) Coil-Processed Product A3.6 Hot-Rolled Product Processed Without Coiling A3.7 Cold-Rolled Product Processed Without Coiling A3.8 Tolerances for Other Dimensional Characteristics TABLE A2.30 TABLE A3.1 TABLE A3.2 TABLE A3.3 TABLE A3.4
19	TABLE A3.5 TABLE A3.6 TABLE A3.7
20	TABLE A3.8 TABLE A3.9 TABLE A3.10 TABLE A3.11 TABLE A3.12 TABLE A3.13
21	TABLE A3.14 TABLE A3.15 TABLE A3.16 TABLE A3.17 TABLE A3.18 TABLE A3.19
22	TABLE A3.20 TABLE A3.21 TABLE A3.22 TABLE A3.23 TABLE A3.24 TABLE A3.25 TABLE A3.26 TABLE A3.27
23	A4. REQUIREMENTS FOR THE INTRODUCTION OF NEW MATERIALS A4.1 TABLE A3.28 TABLE A3.29

Additional information

Standard Title	A480/A480M-05 Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
Published Code	ASTM
Publication Date	2005
Pages Count	24
ICS Codes	77.140.50 - Flat steel products and semi-products

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-A480 2005

PDF Catalog

Related products