ASTM-D2765 2011

$40.63

D2765-11 Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics

Published By	Publication Date	Number of Pages
ASTM	2011	7

Guaranteed Safe Checkout

Categories: 83.080.20 - Thermoplastic materials, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D2765-11

Historical Standard: Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics

ASTM D2765

Scope

1.1 The gel content (insoluble fraction) produced in ethylene plastics by crosslinking is determined by extracting with solvents such as decahydronaphthalene or xylenes. The methods described herein are applicable to crosslinked ethylene plastics of all densities, including those containing fillers, and all provide corrections for the inert fillers present in some of those compounds.

1.2 Test Method A, which permits most complete extraction in least time, is to be used for referee tests, but two alternative nonreferee Test Methods B and C are also described. Test Method B differs from the referee test method only in sample preparation; that is, it requires use of shavings taken at selected points in cable insulation, for example, rather than the ground sample required by the referee test method. Because the shaved particles are larger, less total surface per sample is exposed to the extractant, so this test method ordinarily yields extraction values about 1 to 2 % lower than the referee method. Test Method C requires that a specimen in one piece be extracted in xylenes at a constant temperature of 110°C. At this temperature and with a one-piece specimen, even less extraction occurs (from 3 to 9 % less than the referee test method), this method permits swell ratio (a measure of the degree of crosslinking in the gel phase) be determined.

1.3 Extraction tests are made on articles of any shape. They have been particularly useful for electrical insulations since specimens may be selected from those portions of the insulation most susceptible to insufficient crosslinking.

1.4 The values stated in SI units are to be regarded as standard. The inch-pound units in brackets are for information only.

Note 1—Method B of this test method is equivalent to ISO 10147.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Sections 6, 10, and 25.

15.1 This modification of the referee test method was developed particularly for wire and cable insulations and differs from the referee test method only in specimen preparation.

15.2 In using this alternative test method, it is recognized that the values obtained at times, are lower than those obtained by referee Test Method A for the reason given in 1.2.

20.1 Degree of crosslinking is determined by measuring the swell and extraction occurring in a solvent that attaches that portion of the polymer which is not crosslinked. Both measurements are obtained in one test. The degree of crosslinking is not expressed as a percent of total crosslinkability or similar expression, but is judged from swell ratio and percent extract based on experience with the particular polymer-solvent system under consideration.

20.2 This test method is applicable to crosslinked ethylene plastics of any density and including those containing fillers, provided that the fillers are insoluble in the extractant.

20.3 In using this alternative test method, it is recognized that the extraction values obtained will be lower than those obtained by either Test Method A or Test Method B for the reasons given in 1.2. However, this test method permits swell ratio to be determined.

Keywords

crosslinked ethylene plastics; gel content; insoluble fraction; swell ratio: Crosslinking; Decahydronaphthalene extraction; Ethylene plastics; Gels (fisheyes) content; Insulated wire and cable; Nonreferee method; Referee methods; Swelling; Xylene

ICS Code

ICS Number Code 83.080.20 (Thermoplastic materials)

DOI: 10.1520/D2765-11

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology Summary of Test Methods
2	Significance and Use Precautions Conditioning Apparatus Reagents Safety Precautions Test Specimens
3	Procedure FIG. 1
4	Calculation Report Scope Test Specimens Procedure Calculation FIG. 2
5	Report Scope Summary of Test Method Significance and Use Apparatus Reagents and Materials Safety Precautions Test Specimens Procedure
6	Report Precision and Bias
7	Keywords TABLE 1

Additional information

Standard Title	D2765-11 Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
Published Code	ASTM
Publication Date	2011
Pages Count	7
ICS Codes	83.080.20 - Thermoplastic materials