ASTM-F406 2004

$44.96

F406-04 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards

Published By	Publication Date	Number of Pages
ASTM	2004	19

Guaranteed Safe Checkout

Categories: 97.220.30 - Indoor sports equipment, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM F406-04

Historical Standard: Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards

ASTM F406

Scope

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard.

1.2 This specification covers products intended to provide sleeping and playing accommodations for a child (excluding bassinets, cradles, and baskets) that have an interior length dimension smaller than 49¾ in. (1263 mm) or an interior width dimension smaller than 25 3/8 in. (643 mm), or both. Such products are intended for a child who is less than 35 in. (890 mm) in height.

1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.

1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.

1.5 The following safety hazards caveat pertains only to the test method portion, Section 8 , of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1 – This consumer safety specification includes the following sections:

Keywords

play yard; non-full-size crib

ICS Code

ICS Number Code 97.220.30 (Indoor sports equipment)

DOI: 10.1520/F0406-04

Additional information

Torque Test	8.16.3
Federal Regulations	2.2
ASTM Standards	2.1
Procedure for Plastic Teething Rail Test	8.5.2
Vertical Impact Testing	6.2
Dropside Static Test	8.2.3
Instructional Literature	10
Mesh/Fabric Crib	3.1.10
Folding Latch Test Method	8.8.2
Locking Device	7.4
Dropside Impact Test	8.2.2
Top Rail Covering Material	7.5
Title	Section
Sewn Assembly	7.8.1
Stationary Side	3.1.18
Calibration and Standardization	4
Dropside Locking Device Test Method	8.8.1
Dropside Latch Testing	6.4.1
Occupant	3.1.12
Performance Requirements for Mesh/Fabric Units	7
Foldable Side or End Latch Testing	6.4.2
Terminology	3
Mesh/Fabric Attachment Strength Test Method	8.11
Marking and Labeling	9
Scissoring, Shearing, or Pinching	5.6
Test Methods	8
Removal of Protective Components	8.16
Performance Requirements for Rigid Sided Units	6
Floor Strength Test for Mesh/Fabric Cribs	8.7
Vinyl Thickness Measurement	8.17
Test for Strength of Mesh and Integrity of Attachment	8.10
Locking Mechanism Test	8.8
Mattress Support Impact Test for Rigid Sided Cribs	8.1
Cord Length	5.12
Openings	5.8
Scope	1
Stationary Side or Foldable Side Static Test	8.2.5
Height of Sides	7.1
Fabric Strength	7.7.1
Coil Springs	5.13
Procedure for Horizontally Hinged Dropside Latch Test	8.4.4
Static Load	3.1.17
Rigid Sided Crib	3.1.15
Mattress Support Testing	6.2.4
Test for Attachment of Storage Pouch or Other Parts with Printed Warnings	8.18
Latching and Locking Mechanisms	5.7
Floor Strength	7.3
Tension Test	8.16.4
Procedure for Vertical Dropside Latch Tests	8.4.3
Side or End Impact Test, or Both, for Rigid Sided Cribs	8.2
Side or End Latch Test, or Both, for Rigid Sided Cribs	8.4
Mattress Support System Test for Rigid Sided Cribs	8.3
Test for Stability of Product	8.12
Dropside/Dropgate	3.1.3
Stationary Side or Foldable Side Impact Test	8.2.4
Protective Components	5.9
Manufacturer's Recommended Use Position	3.1.7
Mesh Requirements	7.6
Mesh/Fabric Assembly Requirements	7.8
Water Mattress Use	10.3.4
Structural Failure	3.1.19
Mesh Strength	7.6.2
Side Deflection and Strength	7.2
Seam Strength	7.8.2
Permanency of Labels and Warnings	8.13
Mattress	5.14
Conspicuous	3.1.1
Definitions of Terms Specific to This Standard	3.1
Foldable Side or End	3.1.6
Mesh Openings	7.6.1
Protrusions	8.20
Labeling	9.1
Plastic Teething Rail Test for Rigid Sided Cribs	8.5
Dynamic Load	3.1.4
Side Deflection and Strength Tests for Mesh/Fabric Cribs	8.6
Plastic Teething Rail	6.5
Cord Length Test Method	8.19
Test Procedure for Latches to Prevent Folding of a Foldable Side or End	8.4.5
Seam	3.1.16
Side or End Testing, or Both	6.2.2
Fabric Material Requirements	7.7
Paper Label	3.1.13
Protrusion	3.1.14
Nonpaper Label	3.1.11
Referenced Documents	2
Fabric	3.1.5
Mesh	3.1.9
Warning Statements	10.1.2
Test Method for Dropside Latch	8.4.2
Mesh Opening Test	8.9
Side(s) and/or End(s) Latch Testing	6.4
Mesh/Fabric Attachment Strength	7.8.3
Stability	5.11
Mattress Support System Testing	6.3
General Requirements	5
Cord	3.1.2
ICS Codes	97.220.30 - Indoor sports equipment