BS EN 1096-4:2018
$167.15
Glass in building. Coated glass – Product standard
| Published By | Publication Date | Number of Pages |
| BSI | 2018 | 38 |
This European Standard covers the evaluation of conformity and the factory production control of coated glass for use in buildings. NOTE For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 6 | 1 Scope 2 Normative references |
| 7 | 3 Terms, definitions and symbols 3.1 Terms and definitions |
| 8 | 3.2 Symbols |
| 9 | 4 Product description and characteristics 4.1 Product description 4.2 Determination of the characteristic’s performances 4.2.1 Characteristic of coated glass 4.2.1.1 General |
| 10 | 4.2.1.2 Glass panes used as substrates for the production of coated glass 4.2.2 Determination of characteristics of coated glass 4.2.2.1 General 4.2.2.2 Safety in the case of fire – Resistance to fire 4.2.2.3 Safety in the case of fire – Reaction to fire 4.2.2.4 Safety in the case of fire – External fire performance (for roof coverings only) |
| 11 | 4.2.2.5 Safety in use – Bullet resistance: shatter properties and resistance to attack 4.2.2.6 Safety in use – Explosion resistance: impact behaviour and resistance to impact 4.2.2.7 Safety in use – Burglar resistance: shatter properties and resistance to attack 4.2.2.8 Safety in use – Pendulum body impact resistance: shatter properties (safe breakability) and resistance to impact 4.2.2.9 Safety in use – Mechanical resistance: Resistance against sudden temperature changes and temperature differentials 4.2.2.10 Safety in use – Mechanical resistance: Resistance against wind, snow, permanent load and/or imposed loads of the glass unit 4.2.2.11 Protection against noise – Direct airborne sound reduction 4.2.2.12 Energy conservation and heat retention – Thermal properties 4.2.2.13 Energy conservation and heat retention – Radiation properties: Light transmittance and reflectance |
| 12 | 4.2.2.14 Energy conservation and heat retention – Radiation properties: Solar energy characteristics 4.2.2.15 Durability / Conformity with the definition of coated glass |
| 13 | 4.3 Characteristics other than listed in 4.2 5 Assessment and verification of constancy of performance – AVCP 5.1 General |
| 14 | 5.2 Determination of the product type (see 5.1, 1) 5.2.1 General |
| 15 | 5.2.2 Type testing of characteristic’s performances 5.2.3 Test reports 5.2.4 Multiple lines/sites 5.3 Factory Production control (FPC) 5.3.1 General 5.3.2 Inspection of samples in accordance with a prescribed test plan (see 5.1, 2a) |
| 16 | 5.4 Initial inspection of factory and of factory production control (see 5.1, 2b) |
| 17 | 5.5 Continuous surveillance and assessment of the factory production control (5.1, 2c) |
| 18 | 5.6 Procedure for modifications 5.7 Pre-production products (e.g. prototypes) 6 Marking and/or labelling 6.1 General 6.2 Product marking |
| 19 | Annex A (normative)Factory production control A.1 Factory Production Control Requirements A.1.1 General A.1.2 Organization A.1.2.1 Responsibility and authority A.1.2.2 Management representative for factory production control A.1.2.3 Management review A.1.3 Control system A.1.3.1 General A.1.3.2 Personnel |
| 20 | A.1.3.3 Documentation A.1.4 Equipment A.1.4.1 Testing A.1.4.2 Manufacturing A.1.5 Inspection and testing A.1.6 Non-complying materials / products |
| 21 | A.2 Inspection and testing tables of coated glass production A.2.1 Information on Tables A.1 and A.2 A.2.1.1 General A.2.1.2 Specific requirements A.2.2 Comments specific to Table A.1 |
| 22 | A.2.3 Comments specific to Table A.2 A.2.4 Use of proxy testing |
| 27 | Annex B (informative)Tests for factory production control General B.2 Radiometric properties B.2.1 Sampling |
| 28 | B.2.2 Measurements B.3 Information on ensuring durability conformity |
| 29 | Annex C (normative)Type testing, sampling and measurement of spectrophotometric and energy characteristics C.1 Sampling C.1.1 General C.1.2 Sample specification C.2 Measurement of photometric and energy characteristics |
| 30 | C.3 Tolerances on spectrophotometric characteristics |
| 31 | Annex D (informative)Provisions for voluntary involvement of third party(ies) D.1 General D.2 Voluntary tasks for third parties D.3 Marking and labelling |
| 32 | Annex ZA (informative)Relationship of this European Standard with Regulation (EU) No.305/2011 |
Related products
-
BS EN 1096-4:2018 – TC:2020 Edition
Tracked Changes. Glass in building. Coated glass – Product standard Published By Publication Date Number…
