Shopping Cart

No products in the cart.

BS EN 50194-1:2023 – TC

$217.84

Tracked Changes. Electrical apparatus for the detection of flammable gases in household premises – Test methods and performance requirements

Published By Publication Date Number of Pages
BSI 2023 94
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document specifies general requirements for the construction, testing and performance of electrically operated apparatus for the detection of flammable gases, designed for continuous operation in a fixed installation in household premises. The apparatus can be mains or battery powered. Additional requirements for apparatus to be used in recreational vehicles and similar premises are specified in EN 50194-2. NOTE For caravan holiday homes EN 50194-1 applies. This document specifies four types of apparatus to warn and/or alarm in the event of an escape of town gas, natural gas or liquefied petroleum gas (LPG), Hydrogen and flammable refrigerant gases: — Type A apparatus – provides a visual and audible alarm and an executive action in the form of an output signal that can actuate directly or indirectly a shut-off device and/or other ancillary device in the event of an escape of town gas, natural gas (LNG) liquefied petroleum gas (LPG) and Hydrogen gases; — Type B apparatus – same as Type A but provides a visual and audible alarm only; — Type C apparatus – provides a visual and audible alarm and an executive action in the form of an output signal that can actuate directly or indirectly a shut-off device and/or other ancillary device in the event of an escape of flammable refrigerant gas A2L, A2 or A3 as classified in other International Standards, e.g. ISO 817; — Type D apparatus – intended to be installed where there can be a source of danger to the public, designed for continuous operation in fixed installations in non-classified explosive atmosphere premises (where the requirements for electrical Ex-safety are not requested). Intended for any flammable gases. Typically Type D apparatus are available with analogue or digital output, designed as detection system. These systems are regularly maintained by competent persons and/or have a protection of IP44 or higher. For type D apparatus, EN 60079-29-1 is applied. See Annex C for further clarification on the apparatus types and their application. NOTE Apparatus complying with this document is not considered suitable for installation in potentially explosive atmospheres, in which case the EN 60079 series applies. NOTE Apparatus complying with EN 60079-29-1 will not necessarily comply with this document. This document does not apply to any of the following: — apparatus intended for the detection of dusts or mists in air; — scientific or laboratory-based apparatus used only for analysis or measurement; — apparatus used exclusively for process measurement purposes; — apparatus for medical purposes; — apparatus used for breath alcohol measurement; — apparatus intended for the direct measurement of automotive exhaust gases; — apparatus intended for use in industrial environments.

PDF Catalog

PDF Pages PDF Title
1 30483494
54 A-30440601
55 undefined
62 1 Scope
63 2 Normative references
3 Terms and definitions
65 4 Symbols and abbreviations
66 5 Design requirements
5.1 General requirements
5.2 Construction
5.3 Visual indicators
67 5.4 Alarms
5.5 End-of-life
5.5.1 General
5.5.2 Prediction of end-of-life
5.5.3 Inbuilt testing of end-of-life
5.5.4 End-of-life fault warnings
68 5.6 Fault warnings
5.7 Transmittable output signal (applicable for type A and type C apparatus only)
5.8 Software-controlled apparatus
5.9 Labelling
69 5.10 Requirements for the use of batteries
5.10.1 Battery low voltage warning
5.10.2 Battery capacity
5.10.3 Battery reversal
5.10.4 Battery connections
70 5.10.5 Battery removal feature
5.11 Inter-connectable apparatus
5.12 Back-up power source
5.12.1 General
71 5.12.2 Monitoring of back-up power source
6 Test and performance requirements
6.1 General requirements for tests
6.1.1 Test samples for type testing
72 6.1.2 Preparation of samples
6.1.3 Use of mask for testing
6.1.4 Test chamber
6.1.5 Unpowered storage
6.2 Normal conditions for tests
6.2.1 General
73 6.2.2 Test gases for alarm testing
6.2.3 Speed of air and test gas
6.2.4 Power supply
6.2.5 Temperature
6.2.6 Humidity
6.2.7 Pressure
6.3 Test methods and performance requirements
6.3.1 General
74 6.3.2 Transmittable output signal
6.3.2.1 Test
6.3.2.2 Performance requirement
6.3.3 Alarm set point
6.3.3.1 Pre-set level
6.3.3.2 Test
6.3.3.3 Performance requirements
6.3.4 Alarm during warm-up time
6.3.4.1 Test
6.3.4.2 Performance requirements
6.3.5 Response time
6.3.5.1 Test
75 6.3.5.2 Performance requirement
6.3.6 Temperature effects
6.3.6.1 Test
6.3.6.2 Performance requirement
6.3.7 Humidity effects
6.3.7.1 Test
6.3.7.2 Performance requirement
6.3.8 Air velocity test
6.3.8.1 Test
6.3.8.2 Performance requirement
6.3.9 Supply voltage variations (mains powered apparatus only)
6.3.9.1 Test
6.3.9.2 Performance requirement
76 6.3.10 Electromagnetic compatibility
6.3.10.1 Test
6.3.10.2 Performance requirements
6.3.11 Slow increase of gas volume ratio
6.3.11.1 Test
6.3.11.2 Performance requirements
6.3.12 Effects of other gases
6.3.12.1 Test
77 6.3.12.2 Performance requirement
6.3.13 Long term stability
6.3.13.1 Test
6.3.13.2 Performance requirement
6.3.14 Ignition test
6.3.14.1 Test
78 6.3.14.2 Performance requirement
6.3.15 Refrigerant poisoning and oil spray test (for Type C apparatus only)
6.3.15.1 General
6.3.15.2 Test
6.3.15.3 Performance requirement
6.3.16 Alarm sound level
6.3.16.1 Test
79 6.3.16.2 Performance requirements
6.3.17 Degree of protection
6.3.17.1 Test
6.3.17.2 Performance requirement
6.3.18 Mechanical strength
6.3.18.1 Test
6.3.18.2 Performance requirement
6.3.19 Stability in high humidity test (for type C apparatus)
6.3.19.1 Test
6.3.19.2 Performance requirement
80 6.3.20 Stability to low humidity test (for type C apparatus)
6.3.20.1 Test
6.3.20.2 Performance requirement
7 Apparatus using radio links
7.1 General
7.1.1 General
7.1.2 RF range and reproducibility tests
7.1.3 Failure of radio link
7.1.4 Identification codes
7.1.5 Environmental requirements
81 7.2 Radio link tests
7.2.1 RF Range
7.2.1.1 General
7.2.1.2 Transmission power test procedure
7.2.1.3 Receiver test
7.2.2 Failure of radio link tests
7.2.2.1 Test
7.2.2.2 Performance requirements
7.2.3 Identification codes verification tests
82 7.2.4 Environmental tests
7.2.4.1 Test
7.2.4.2 Performance requirements
8 Self-contained battery powered apparatus
8.1 Battery low voltage warning
8.1.1 General
8.1.2 Test
83 8.1.3 Performance requirements
8.2 Battery capacity
8.2.1 General
8.2.2 Assessment
8.2.3 Performance requirements
8.3 Battery reversal
8.3.1 General
8.3.2 Test
8.3.3 Performance requirements
84 8.4 Battery connections with flexible leads only
8.4.1 General
8.4.2 Test
8.4.3 Performance requirements
8.5 Back-up power source
8.5.1 Objective
8.5.2 Test
8.5.2.1 Low back-up
8.5.2.2 Open circuit
8.5.2.3 Short-circuit
8.5.3 Performance requirements
85 9 User instructions
9.1 General
86 9.2 Instructions for apparatus with replaceable sensor
9.3 Instructions on location of the gas detection apparatus
9.4 Instructions on emergency actions
87 10 Packaging
88 Annex A (informative)Test arrangement schematics for sound level test
89 Annex B (informative)Calculation of the expected battery service life
B.1 General requirements
B.2 Example
B.2.1 Capacity required for 1 year operation in milli Ampere hours (mAh)
B.2.2 Capacity required for 4 min alarm
B.2.3 Capacity required for 30 days audible battery low voltage warning
90 B.2.4 Alarm Voltage Operating Range
B.2.5 Battery Data
B.2.6 Expected Service Life
91 Annex C (informative)Clarification of the Type A, Type B, Type C and Type D apparatus
BS EN 50194-1:2023 - TC
$217.84