🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS IEC 60115-2-10:2023

BS IEC 60115-2-10:2023

$189.07

Fixed resistors for use in electronic equipment – Blank detail specification: Low-power film resistors with leads for through-hole assembly on circuit boards (THT), for general electronic equipment, classification level G

Published By Publication Date Number of Pages
BSI 2023 50
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

PDF Catalog

PDF Pages PDF Title
2 undefined
4 CONTENTS
7 FOREWORD
9 0 Introduction to the template provided by this blank detail specification
0.1 Scope of this blank detail specification
0.2 Function of this blank detail specification
10 0.3 Identification of the detail specification and the resistor
12 1 Scope
2 Normative references
13 3 Terms and definitions
4 Characteristics and ratings
4.1 General
4.2 Dimensions
14 Figures
Figure 1 – Outline and dimensions
Tables
Table 1 – Styles and dimensions
15 Figure 2 – Lead eccentricity of the wire terminations
Figure 3 – Length of excessive coating on the wire terminations
16 4.3 Ratings
Table 2 – Climatic categories
Table 3 – Ratings
17 4.4 Resistance range and tolerance on resistance
Figure 4 – Derating curve
18 5 Tests and test severities
5.1 General
5.2 Resistance
Table 4 – Temperature coefficients, tolerances and resistance ranges for climatic category … / … / …
19 5.3 Temperature coefficient of resistance
5.4 Temperature rise
5.5 Endurance at the rated temperature 70 °C
5.6 Endurance at a maximum temperature: UCT
5.7 Short-term overload
20 5.8 Electrostatic discharge (ESD) test
5.9 Visual examination
5.10 Gauging of dimensions
5.11 Detail dimensions
Table 5 – Short-term overload duration
Table 6 – ESD test voltages
21 5.12 Robustness of terminations
5.13 Vibration
5.14 Rapid change of temperature
5.15 Climatic sequence
5.16 Damp heat, steady state
Table 7 – Additional cycles of the damp heat, cyclic test
22 5.17 Solderability, with lead-free solder
5.18 Solderability, with SnPb solder
5.19 Resistance to soldering heat
Table 8 – Damp heat, steady state test duration
23 5.20 Solvent resistance
5.21 Insulation resistance
5.22 Voltage proof
5.23 Flammability
6 Performance requirements
6.1 General
24 6.2 Limits for change of resistance at tests
6.3 Temperature coefficient of resistance
Table 9 – Limits for change of resistance at tests
25 6.4 Temperature rise
6.5 Visual examination
6.5.1 General visual criteria
Table 10 – Permitted change of resistance due to the variation of temperature
26 6.5.2 Visual criteria after tests
6.5.3 Visual criteria for packaging
6.6 Solderability
6.7 Insulation resistance
27 6.8 Flammability
7 Marking, packaging and ordering information
7.1 Marking of the component
7.2 Packaging
7.3 Marking of the packaging
7.4 Ordering information
28 8 Additional information
8.1 General
8.2 Storage and transportation
8.3 Substrate for assembly
8.4 Soldering process
8.5 Use of cleaning agents or solvents
29 8.6 Coating or potting after assembly
9 Quality assessment procedures
9.1 General
9.1.1 100 % test
9.1.2 Certificate of conformity (CoC)
30 9.1.3 Certified test records of released lots
9.2 Qualification approval
9.3 Maintenance of a qualification approval
9.3.1 Quality conformance inspection
9.3.2 Non-conforming specimen
31 Table 11 – Test schedule for the qualification approval
35 Table 12 – Test schedule for quality conformance inspection
39 Annex A (normative)Symbols and abbreviated terms
A.1 Symbols
41 A.2 Abbreviated terms
42 Annex B (normative)Reference for visual examination
43 Annex C (normative)Zero ohm resistors (jumpers)
C.1 General
C.2 Characteristics and ratings
Table C.1 – Climatic category
Table C.2 – Ratings for 0 Ω resistors
44 C.3 Tests and test severities
C.4 Performance requirements
C.5 Marking, packaging and ordering information
C.6 Additional information
C.7 Quality assessment procedures
C.7.1 Test schedule for qualification approval
45 C.7.2 Test schedule for quality conformance inspection
46 Annex X (informative)Cross-references to the prior edition of this specification
Table X.1 – Cross-references to clauses of the prior edition
47 Bibliography

Related products

BS IEC 60115-2-10:2023
$189.07