BS ISO 6361-2:2014
$198.66
Wrought aluminium and aluminium alloys. Sheets, strips and plates – Mechanical properties
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 60 |
In conjunction with ISO 6361-1, this part of ISO 6361 specifies the mechanical properties of wrought aluminium and aluminium alloy sheets, strips, and plates for general engineering applications.
It applies to flat-rolled products.
The chemical composition of these materials is given in ISO 6361-5.
The designations of aluminium and aluminium alloys and the temper designations used in this part of ISO 6361 are in accordance with ISO 2107.
NOTE In certain countries, for purposes of mechanical properties, the thickness limit can be lowered to 0,15 mm by agreement between the purchaser and the supplier, in the case of sheets and strips.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Section sec_1 Section sec_2 Section sec_3 Section sec_4 Section sec_5 1 Scope 2 Normative references 3 Terms and definitions 4 Tensile testing 5 Bend testing |
| 8 | Section sec_6 Section sec_6.1 Section sec_6.2 Table tab_1 6 Mechanical properties 6.1 Tensile test 6.2 Bend test |
| 9 | Table tab_2 |
| 10 | Table tab_3 |
| 11 | Table tab_4 |
| 12 | Table tab_5 |
| 13 | Table tab_6 Table tab_7 |
| 15 | Table tab_8 |
| 16 | Table tab_9 Table tab_10 |
| 17 | Table tab_11 Table tab_12 |
| 18 | Table tab_13 |
| 20 | Table tab_14 Table tab_15 |
| 21 | Table tab_16 |
| 22 | Table tab_17 Table tab_18 |
| 23 | Table tab_19 Table tab_20 |
| 24 | Table tab_21 Table tab_22 |
| 25 | Table tab_23 |
| 26 | Table tab_24 |
| 27 | Table tab_25 |
| 28 | Table tab_26 Table tab_27 Table tab_28 |
| 29 | Table tab_29 Table tab_30 |
| 30 | Table tab_31 |
| 31 | Table tab_32 |
| 32 | Table tab_33 |
| 33 | Table tab_34 |
| 34 | Table tab_35 |
| 35 | Table tab_36 |
| 36 | Table tab_37 Table tab_38 |
| 37 | Table tab_39 Table tab_40 |
| 38 | Table tab_41 Table tab_42 Table tab_43 Table tab_44 |
| 39 | Table tab_45 |
| 40 | Table tab_46 |
| 41 | Table tab_47 Table tab_48 Table tab_49 |
| 42 | Table tab_50 |
| 43 | Table tab_51 |
| 44 | Table tab_52 Table tab_53 |
| 45 | Table tab_54 |
| 46 | Table tab_55 Table tab_56 Table tab_57 |
| 47 | Table tab_58 |
| 48 | Table tab_59 Table tab_60 |
| 49 | Table tab_61 Table tab_62 |
| 50 | Table tab_63 |
| 56 | Annex sec_A Annex sec_A.1 Annex sec_A.2 Annex sec_A.3 Annex A (normative) Rules for rounding results obtained by inspection and testing |
| 57 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Reference ref_6 Reference ref_7 Reference ref_8 Reference ref_9 Reference ref_10 Bibliography |
