ISO 13000-1:2021
$19.50
Plastics — Polytetrafluoroethylene (PTFE) semi-finished products — Part 1: Requirements and designation
| Published By | Publication Date | Number of Pages |
| ISO | 2021-08 | 16 |
This document establishes a system of designation for processed unfilled polytetrafluoroethylene (PTFE) products, which can occur in several forms.
The PTFE used to make the semi-finished product is described in ISO 20568-1. The PTFE used to make the semi-finished product are virgin, reprocessed or recycled resin. The addition of up to 1,5 % by mass of pigment or colorant can be used.
Related products
-
BSI 22/30402442 DC 2022
BS ISO 10300-1. Calculation of load capacity of bevel gears – Part 1. Introduction and…
-
BS ISO 15000-1:2021
Electronic business eXtensible Markup Language (ebXML) – Messaging service core specification Published By Publication Date…
-
BS ISO 13400-2:2012
Road vehicles. Diagnostic communication over Internet Protocol (DoIP) – Transport protocol and network layer services…
-
BSI 20/30408960 DC 2020
BS EN ISO 13000-1. Plastics. Polytetrafluoroethylene (PTFE) semi-finished products – Part 1. Requirements and designation…
-
ISO 13000-2:2021
Plastiques — Semi-produits en polytétrafluoroéthylène (PTFE) — Partie 2: Préparation des éprouvettes et détermination des…
-
BS ISO 10300-1:2001
Calculation of load capacity of bevel gears – Introduction and general influence factors Published By…
-
BS EN ISO 13000-1:2021 – TC
Tracked Changes. Plastics. Polytetrafluoroethylene (PTFE) semi-finished products – Requirements and designation Published By Publication Date…
-
BS ISO 16000-28:2020
Indoor air – Determination of odour emissions from building products using test chambers Published By…
-
ASTM-D1710:2021 Edition
D1710-15(2021) Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes Published…
-
ASME QME 1 2023
ASME QME-1 – 2023: Qualification of Active Mechanical Equipment Used in Nuclear Facilities Published By…
-
ISO/TS 15000-5:2005/Amd 1:2011
Electronic Business Extensible Markup Language (ebXML) — Part 5: ebXML Core Components Technical Specification, Version…
-
BS ISO 16000-18:2011:2012 Edition
Indoor air – Detection and enumeration of moulds. Sampling by impaction Published By Publication Date…
-
BS ISO/IEC 18047-63:2023
Information technology. Radio frequency identification device conformance test methods – Test methods for air interface…
-
BS ISO 13400-3:2011:2012 Edition
Road vehicles. Diagnostic communication over Internet Protocol (DoIP) – Wired vehicle interface based on IEEE…
-
ISO 10300-1:2001
Calculation of load capacity of bevel gears — Part 1: Introduction and general influence factors…
-
BS ISO 10300-1:2023 – TC
Tracked Changes. Calculation of load capacity of bevel gears – Introduction and general influence factors…
-
BS ISO 15000-1:2021
Electronic business eXtensible Markup Language (ebXML) – Messaging service core specification Published By Publication Date…
-
BSI 21/30433926 DC:2021 Edition
BS ISO/IEC 23000-19 AMD2. Information technology. Multimedia application format (MPEG-A) – Part 19. Common media…
-
ISO/IEC 29173-1:2012
Information technology — Mobile item identification and management — Part 1: Mobile RFID interrogator device…
-
BS ISO 13400-1:2011
Road vehicles. Diagnostic communication over internet protocol (DoIP) – General information and use case definition…
-
BS ISO 16000-6:2011:2012 Edition
Indoor air – Determination of volatile organic compounds in indoor and test chamber air by…
-
BS EN ISO 13000-1:2021
Plastics. Polytetrafluoroethylene (PTFE) semi-finished products – Requirements and designation Published By Publication Date Number of…
-
BS EN ISO 13000-2:2021 – TC
Tracked Changes. Plastics. Polytetrafluoroethylene (PTFE) semi-finished products – Preparation of test specimens and determination of…
-
ISO 15000-2:2021
Electronic business eXtensible Markup Language (ebXML) — Part 2: Applicability Statement (AS) profile of ebXML…
-
ISO 13400-1:2011
Road vehicles — Diagnostic communication over Internet Protocol (DoIP) — Part 1: General information and…
-
BSI 23/30464137 DC:2023 Edition
BS EN ISO/IEC 23000-19 AMD 1. Information technology. Multimedia application format (MPEG-A) – Part 19.…
-
ISO/IEC 23200-1:2021
Information technology — Radio frequency identification for item management — Part 1: Interference rejection performance…
-
BS EN ISO 13000-2:2005:2006 Edition
Plastics. Polytetrafluoroethylene (PTFE) semi-finished products – Preparation of test specimens and determination of properties Published…
-
BS ISO 10300-2:2014
Calculation of load capacity of bevel gears – Calculation of surface durability (pitting) Published By…
-
BS ISO/IEC 18000-6:2010
Information technology. Radio frequency identification for item management – Parameters for air interface communications at…
-
ISO/IEC 23000-12:2010/Amd 1:2011
Information technology — Multimedia application format (MPEG-A) — Part 12: Interactive music application format —…
-
BSI PD ISO/IEC TR 20000-10:2015
Information technology. Service management – Concepts and terminology Published By Publication Date Number of Pages…
-
ISO 15000-1:2021
Electronic business eXtensible Markup Language (ebXML) — Part 1: Messaging service core specification Published By…
-
BS ISO 16000-3:2001
Indoor air – Determination of formaldehyde and other carbonyl compounds. Active sampling method Published By…
-
BS EN 1459-4:2020:2021 Edition
Rough-terrain trucks. Safety requirements and verification – Additional requirements for variable-reach trucks handling freely suspended…
-
ISO/IEC 23000-11:2009/Amd 1:2011
Information technology — Multimedia application format (MPEG-A) — Part 11: Stereoscopic video application format —…
-
BS EN ISO 13000-1:2005
Plastics. Polytetrafluoroethylene (PTFE) semi-finished products – Requirements and designation Published By Publication Date Number of…
-
BS ISO 16000-3:2011
Indoor air – Determination of formaldehyde and other carbonyl compounds in indoor air and test…
-
DIN EN ISO 13000-1:2021 Edition
Kunststoffe – Polytetrafluorethylen (PTFE)-Halbzeuge – Teil 1: Anforderungen und Bezeichnung Published By Publication Date Number…
-
BS EN ISO 13000-2:2021
Plastics. Polytetrafluoroethylene (PTFE) semi-finished products – Preparation of test specimens and determination of properties Published…
