Revision Standard – Active. Certain electrical, dimensional, and mechanical characteristics are covered in this standard. It also takes into consideration certain safety features of three-phase, 60 Hz, liquid-immersed, self-cooled, submersible transformers with separable insulated high-voltage connectors. These transformers are rated 3750 kVA and smaller with high voltages of 34 500 GrdY\/19 920 V and below and with low voltages of 600 V and below.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | IEEE Std C57.12.24-2016 Front Cover <\/td>\n<\/tr>\n | ||||||
| 2<\/td>\n | Title page <\/td>\n<\/tr>\n | ||||||
| 4<\/td>\n | Important Notices and Disclaimers Concerning IEEE Standards Documents <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Participants <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 1. Overview 1.1 Scope 1.2 Purpose 2. Normative references <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 3. Definitions 4. Service conditions 4.1 Cooling air temperature limit 4.2 Submerged operation <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 5. Rating data 5.1 Cooling class 5.2 Kilovolt-ampere ratings 5.3 Voltage ratings 5.4 Insulation levels <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 5.5 Impedance voltage 5.5.1 General 5.5.2 Tolerance on impedance voltage 6. Tests 6.1 General <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 6.2 Reference temperature 7. Construction 7.1 General <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 7.2 Connectors and terminals 7.2.1 High-voltage connectors <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 7.2.2 Low-voltage terminals <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 7.2.3 Neutral terminal connections 7.3 Accessories 7.3.1 Tap changer <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 7.3.2 Pressure relief 7.3.2.1 Manual pressure relief 7.3.2.2 Automatic pressure relief 7.3.3 Loadbreak switch 7.3.3.1 Loadbreak switch labeling <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | 7.3.3.2 Loadbreak switch location 7.3.3.3 Loadbreak switch rotation 7.3.3.4 Loadbreak switch current-carrying capabilities 7.3.3.5 Loadbreak switch material 7.3.4 Overcurrent protection 7.3.4.1 Full range, current-limiting fuses 7.3.4.2 Bayonet fuses <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 7.3.5 Protective covers 7.4 Nameplate 7.5 Tank 7.5.1 Material requirements 7.5.1.1 Transformers located in a wet vault or manhole <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 7.5.1.2 Transformers located in a vault or manhole with cycling conditions 7.5.1.3 Material thickness 7.5.2 Tank integrity 7.5.3 Hardware 7.5.4 Other materials 7.5.5 Cover <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 7.5.6 Hand holes 7.5.7 Base 7.5.8 Lifting provisions 7.5.9 Grounding provisions 7.5.10 Finish <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | 7.5.11 Insulating liquid level marking 7.5.12 Connector and terminal markings 7.6 Components for primary cable system 7.7 Angular displacement 7.8 Audible sound levels <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | 8. Storage and installation 8.1 Storage 8.2 Installation <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | Annex A (informative) Use of pressure relief means <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | Annex B (informative) Bibliography <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | Back cover <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Standard for Submersible, Three-Phase Transformers, 3750 kVA and Smaller: High Voltage, 34 500 GrdY\/19 920 Volts and Below; Low Voltage, 600 Volts and Below<\/b><\/p>\n |