{"id":248174,"date":"2024-10-19T16:20:47","date_gmt":"2024-10-19T16:20:47","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-61280-2-22012\/"},"modified":"2024-10-25T11:29:34","modified_gmt":"2024-10-25T11:29:34","slug":"bs-en-61280-2-22012","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-61280-2-22012\/","title":{"rendered":"BS EN 61280-2-2:2012"},"content":{"rendered":"
This standard specifies a gauging system for metric taper external threads and mating parallel internal threads as specified in DIN 158-1.<\/p>\n
Gauging of parallel internal threads is to be carried out as specified in ISO 1502.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
6<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | 4 Apparatus 4.1 General <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | 4.2 Reference receiver definition 4.3 Time-domain optical detection system 4.3.1 Overview Figure 1 \u2013 Optical eye pattern, waveform and extinction ratio measurement configuration <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 4.3.2 Optical-to-electrical (O\/E) converter 4.3.3 Linear-phase low-pass filter <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 4.3.4 Oscilloscope Figure 2 \u2013 Oscilloscope bandwidths commonly used in eye pattern measurements <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 4.4 Overall system response 4.5 Oscilloscope synchronization system 4.5.1 General Table 1 \u2013 Frequency response characteristics <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 4.5.2 Triggering with a clean clock 4.5.3 Triggering using a recovered clock <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 4.5.4 Triggering directly on data Figure 3 \u2013 PLL jitter transfer function and resulting observed jitter transfer function <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 4.6 Pattern generator 4.7 Optical power meter 4.8 Optical attenuator 4.9 Test cord 5 Signal under test 6 Instrument set-up and device under test set-up <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 7 Measurement procedures 7.1 Overview 7.2 Extinction ratio measurement 7.2.1 Configure the test equipment 7.2.2 Measurement procedure <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | 7.2.3 Extinction ratio calculation Figure 4 \u2013 Histograms centred in the central 20 % of the eye used to determine the mean logic one and 0 levels, b1 and b0 <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 7.3 Eye amplitude 7.4 Optical modulation amplitude (OMA) measurement using the square wave method 7.4.1 General 7.4.2 Oscilloscope triggering 7.4.3 Amplitude histogram, step 1 <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | 7.4.4 Amplitude histogram, step 2 7.4.5 Calculate OMA 7.5 Contrast ratio (for RZ signals) 7.6 Jitter measurements Figure 5 \u2013 OMA measurement using the square wave method <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | 7.7 Eye width 7.8 Duty cycle distortion (DCD) <\/td>\n<\/tr>\n | ||||||
22<\/td>\n | 7.9 Crossing percentage Figure 6 \u2013 Construction of the duty cycle distortion measurement <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | 7.10 Eye height 7.11 Q-factor\/signal-to-noise ratio (SNR) 7.12 Rise time Figure 7 \u2013 Construction of the crossing percentage measurement <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | 7.13 Fall time Figure 8 \u2013 Construction of the risetime measurement with no reference receiver filtering <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | 8 Eye-diagram analysis using a mask 8.1 Eye mask testing using the \u2018no hits\u2019 technique Figure 9 \u2013 Illustrations of several RZ eye-diagram parameters <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | 8.2 Eye mask testing using the \u2018hit-ratio\u2019 technique Figure 10 \u2013 Basic eye mask and coordinate system <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | 9 Test result 9.1 Required information 9.2 Available information 9.3 Specification information Figure 11 \u2013 Mask margins at different sample population sizes <\/td>\n<\/tr>\n | ||||||
29<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Fibre optic communication subsystem test procedures – Digital systems. Optical eye pattern, waveform and extinction ratio measurement<\/b><\/p>\n |