{"id":421074,"date":"2024-10-20T06:34:18","date_gmt":"2024-10-20T06:34:18","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-60317-562017-2\/"},"modified":"2024-10-26T12:18:07","modified_gmt":"2024-10-26T12:18:07","slug":"bs-en-60317-562017-2","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-60317-562017-2\/","title":{"rendered":"BS EN 60317-56:2017"},"content":{"rendered":"
This part of IEC 60317 specifies the requirements of solderable fully insulated (FIW) zero-defect enamelled round copper wire, class 180, with a single coating based on polyurethane resin, which may be modified providing it retains its chemical identity and satisfies all the required technical specifications.<\/p>\n
The range of nominal conductor diameters of the wires covered by this standard is as follows:<\/p>\n
Grade of FIW 4, 6, 8: 0,090 mm up to and including 0,900 mm.<\/p>\n<\/li>\n<\/ul>\n
Nominal conductor diameters are specified in IEC 60317-0-7\u2013.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions, general notes and appearance 3.1 Terms and definitions 3.2 General notes 3.2.1 Methods of test 3.2.2 Winding wire <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 3.3 Appearance 4 Dimensions 5 Electrical resistance 6 Elongation 7 Springiness 8 Flexibility and adherence 9 Heat shock 10 Cut-through 11 Resistance to abrasion (for nominal diameters of 0,250 mm up to and including 0,900 mm) <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 12 Resistance to solvents 13 Breakdown voltage 14 Continuity of insulation 15 Temperature index 16 Resistance to refrigerants 17 Solderability Table 1 \u2013 Resistance to abrasion <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 18 Heat or solvent bonding 19 Dielectric dissipation factor 20 Resistance to transformer oil 21 Loss of mass 23 Pin-hole test 30 Packaging <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | Annex A (informative) Resistance to abrasion A.1 Grades of FIW 3, 5, 7, 9 A.2 Grades 3 through 9 Table A.1 \u2013 Resistance to abrasion of FIW grades 3 through 9 <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Specifications for particular types of winding wires – Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180<\/b><\/p>\n |