AWWA C151 2009

$75.83

AWWA C151-09: Ductile Iron Pipe, Centrifigually Cast, For Water

Published By	Publication Date	Number of Pages
AWWA	2009	52

Guaranteed Safe Checkout

Category: AWWA

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This standard covers 3-in. through 64-in. (76 mm through 1,600 mm) ductile iron pipe, centrifugally cast, for water, with push-on joints or mechanical joints.

PDF Catalog

PDF Pages	PDF Title
1	ANSI/AWWA C151/A21.51-09
3	Committee Personnel
7	Contents
9	Foreword I. Introduction.
11	II. Special Issues. III. Use of This Standard.
12	IV. Major Revisions. V. Comments.
13	AWWA Standard Ductile-Iron Pipe, Centrifugally Cast SECTION 1: GENERAL Sec. 1.1 Scope Sec. 1.2 Purpose Sec. 1.3 Application
14	SECTION 2: REFERENCES SECTION 3: DEFINITIONS
15	SECTION 4: REQUIREMENTS Sec. 4.1 Materials Sec. 4.2 Permeation
16	Sec. 4.3 General Requirements Sec. 4.4 Coatings and Linings
17	Sec. 4.5 Tolerances or Permitted Variations Sec. 4.6 Weighing Pipe Sec. 4.7 Marking Pipe
18	SECTION 5: VERIFICATION Sec. 5.1 Inspection Sec. 5.2 Test Procedures
20	Sec. 5.3 Additional Control Tests by the Manufacturer
21	Sec. 5.4 Foundry Records Sec. 5.5 Additional Tests Required by the Purchaser
22	Sec. 5.6 Defective Specimens and Retests Sec. 5.7 Basis for Rejection SECTION 6: DELIVERY Sec. 6.1 Notice of Nonconformance Sec. 6.2 Affidavit of Compliance
23	Table 1 Standard dimensions and weights of push-on-joint ductile-iron pipe
24	Table 1 Standard dimensions and weights of push-on-joint ductile-iron pipe (continued)
25	Table 2 Standard dimensions and weights of mechanical-joint ductile-iron pipe
26	Table 3 Dimensions and weights for special thickness classes of push-on-joint ductile-iron pipe
27	Table 3 Dimensions and weights for special thickness classes of push-on-joint ductile-iron pipe (continued)
28	Table 3 Dimensions and weights for special thickness classes of push-on-joint ductile-iron pipe (continued)
29	Table 3 Dimensions and weights for special thickness classes of push-on-joint ductile-iron pipe (continued)
30	Table 4 Dimensions and weights for special thickness classes
31	Table 4 Dimensions and weights for special thickness classes (continued)
32	Table 4 Dimensions and weights for special thickness classes (continued)
33	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load
34	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load (continued)
35	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load (continued)
36	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load (continued)
37	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load (continued)
38	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load (continued)
39	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load (continued)
40	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load (continued)
41	Table 5 Nominal thicknesses for standard pressure classes for earth load plus truck load (continued)
42	Table 6 Nominal thicknesses for standard pressure classes for internal pressure
43	Table 7 Rated working pressure and maximum depth of cover
44	Table 7 Rated working pressure and maximum depth of cover (continued)
47	APPENDIX A Pipe Th ickness Required for Diff erent Tap Sizes Table A.1 Pipe thicknesses required for different tap sizes as per ASME* B1.20.1 for standard taper pipe threads with two, three, and four full threads
48	Table A.1 Pipe thicknesses required for different tap sizes as per ASME* B1.20.1 for standard taper pipe threads with two, three, and four full threads (continued)
49	Table A.2 Pipe thicknesses required for different tap sizes as per ANSI/AWWA C800 for standard corporation stop threads with two, three, and four full threads
50	Table A.2 Pipe thicknesses required for different tap sizes as per ANSI/AWWA C800 for standard corporation stop threads with two, three, and four full threads (continued)