BS EN IEC 61169-68:2022

$167.15

Radio-frequency connectors – Sectional specification for series TRK bayonet coupling triaxial connectors

Published By	Publication Date	Number of Pages
BSI	2022	34

Guaranteed Safe Checkout

Categories: 33.120.30 - RF connectors, BSI

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for series TRK bayonet coupling triaxial connectors. The series TRK bayonet coupling triaxial connectors having the advantages of quick connection and separation, high reliability, small size, good salt characteristics, four polarizations to prevent error-mate etc., can be connected to symmetrically twisted pair cables or triaxial cables. They have been widely used in 1553B data bus systems or other communication systems for digital signal transmission. It specifies mating face dimensions for series TRK bayonet coupling triaxial connectors, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series TRK triaxial connectors. This document indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H. NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for reference purpose only.

PDF Catalog

PDF Pages	PDF Title
2	undefined
5	Annex ZA (normative)Normative references to international publicationswith their corresponding European publications
8	English CONTENTS
10	FOREWORD
12	1 Scope 2 Normative references 3 Terms and definitions
13	4 Mating face and gauge information 4.1 Mating face dimensions 4.1.1 Plug connector Figures Figure 1 – Plug connector Tables Table 1 – Dimensions of plug connector
14	Figure 2 – Locating grooves polarization of plug connector Figure 3 – A polarization mating face of plug connector with three bayonets
15	Figure 4 – D polarization mating face of plug connector with four bayonets Table 2 – A polarization mating face dimensions of plug connector with three bayonets Table 3 – D polarization mating face dimensions of plug connector with four bayonets
16	Figure 5 – Unfolded drawing of A polarization bayonet groove of plug connector Figure 6 – Unfolded drawing of D polarization bayonet groove of plug connector Table 4 – Unfolded drawing dimensions of A polarizationbayonet groove of plug connector
17	4.1.2 Receptacle connector Figure 7 – Receptacle connector Table 5 – Unfolded drawing dimensions of D polarizationbayonet groove of plug connector
18	Figure 8 – Locating keys polarization of receptacle connector Table 6 – Dimensions of receptacle connector
19	Figure 9 – A polarization mating face of receptacle connector with three bayonets Figure 10 – D polarization mating face of receptacle connector with four bayonets Table 7 – A polarization mating face dimensionsof receptacle connector with three bayonets
20	4.1.3 Coaxial pin contact 4.1.4 Coaxial socket contact Figure 11 – Coaxial pin contact Table 8 – D polarization mating face dimensions ofreceptacle connector with four bayonets Table 9 – Dimensions of coaxial pin contact
21	4.2 Gauges for resilient contact 4.2.1 Gauge for socket centre contact Figure 12 – Coaxial socket contact Figure 13 – Gauge for socket centre contact Table 10 – Dimensions of coaxial socket contact Table 11 – Dimensions of gauge for socket centre contact
22	4.2.2 Gauge for socket intermediate contact Figure 14 – Gauge for socket intermediate contact Table 12 – Dimensions of gauge for socket intermediate contact
23	5 Quality assessment procedure 5.1 General 5.2 Rating and characteristics Table 13 – Ratings and characteristics
25	5.3 Test schedule and inspection requirements 5.3.1 Acceptance tests
26	5.3.2 Periodic tests Table 14 – Acceptance tests Table 15 – Periodic tests
27	5.3.3 Procedures for qualification approval
28	6 Instructions for preparation of detail specifications (DS) 6.1 General 6.2 Identification of the component 6.3 Performance 6.4 Marking, ordering information and related matters 6.5 Selection of tests, test conditions and severities
29	6.6 Blank detail specification pro-forma for series TRK bayonet coupling triaxial connectors