ASTM-A6 2005

$67.71

A6/A6M-05e1 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

Published By	Publication Date	Number of Pages
ASTM	2005	61

Guaranteed Safe Checkout

Categories: 77.140.60 - Steel bars and rods, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM A6/A6M-05e1

Historical Standard: Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

ASTM A6/A6M

Scope

1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by ASTM:

1.2 Annex A1 lists permitted variations in dimensions and mass (Note 1) in SI units. The values listed are not exact conversions of the values in Tables 1 to 31 inclusive but are, instead, rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification designation is used.

Note 1—The term “weight” is used when inch-pound units are the standard; however, under SI, the preferred term is “mass.”

1.3 Annex A2 lists the dimensions of some shape profiles.

1.4 Appendix X1 provides information on coil as a source of structural products.

1.5 Appendix X2 provides information on the variability of tensile properties in plates and structural shapes.

1.6 Appendix X3 provides information on weldability.

1.7 Appendix X4 provides information on cold bending of plates, including suggested minimum inside radii for cold bending.

1.8 This general requirements specification also covers a group of supplementary requirements that are applicable to several of the above product specifications as indicated therein. Such requirements are provided for use where additional testing or additional restrictions are required by the purchaser, and apply only where specified individually in the purchase order.

1.9 In case of any conflict in requirements, the requirements of the applicable product specification prevail over those of this general requirements specification.

1.10 Additional requirements that are specified in the purchase order and accepted by the supplier are permitted, provided that such requirements do not negate any of the requirements of this general requirements specification or the applicable product specification.

1.11 For purposes of determining conformance with this general requirements specification and the applicable product specification, values are to be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.

1.12 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.

1.13 This general requirements specification and the applicable product specification are expressed in both inch-pound units and SI units; however, unless the order specifies the applicable “M” specification designation (SI units), the structural product is furnished to inch-pound units.

1.14 The text of this general requirements specification contains notes and/or footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

Keywords

bars; general requirements; plates; rolled; shapes; sheet piling; structural steel

ICS Code

ICS Number Code 77.140.60 (Steel bars and rods)

DOI: 10.1520/A0006_A0006M-05E01

PDF Catalog

PDF Pages	PDF Title
1	Scope
2	Referenced Documents Terminology
4	Ordering Information Materials and Manufacture Heat Treatment Chemical Analysis
5	Metallurgical Structure Quality
6	TABLE
8	Test Methods Tension Tests
10	TABLE TABLE
11	Permitted Variations in Dimensions and Weight [Mass]
12	TABLE 1 TABLE 2
13	TABLE 3 TABLE 4 TABLE 5
14	Retests TABLE 6 TABLE 7 TABLE 8 TABLE 9 TABLE 10 TABLE 11 TABLE 12
15	TABLE 13 TABLE 14
16	Test Reports TABLE 15
17	TABLE 16
18	TABLE 17 TABLE 18
19	Inspection and Testing Retreatment Rejection Identification of Structural Products TABLE 19 TABLE 20
20	TABLE 21 TABLE 22
21	TABLE 23 TABLE 24 TABLE 25
22	TABLE 26 TABLE 27 TABLE 28
23	TABLE 29 TABLE 30 TABLE 31
24	Packaging, Marking, and Loading for Shipment Keywords
26	TABLE S27.1 TABLE S27.2
27	TABLE S27.3 TABLE S27.4
28	A1. PERMITTED VARIATIONS IN DIMENSIONS AND MASS IN SI UNITS A1.1
29	TABLE A1.1
30	TABLE A1.2
31	TABLE A1.3 TABLE A1.4 TABLE A1.5
32	TABLE A1.6 TABLE A1.7 TABLE A1.8 TABLE A1.9
33	TABLE A1.10 TABLE A1.11 TABLE A1.12 TABLE A1.13
34	TABLE A1.14
35	TABLE A1.15
36	TABLE A1.16
37	TABLE A1.17 TABLE A1.18
38	TABLE A1.19 TABLE A1.20 TABLE A1.21
39	TABLE A1.22 TABLE A1.23 TABLE A1.24
40	TABLE A1.25 TABLE A1.26 TABLE A1.27
41	TABLE A1.28 TABLE A1.29 TABLE A1.30 TABLE A1.31
42	A2. DIMENSIONS OF STANDARD SHAPE PROFILES A2.1
43	TABLE A2.1
48	TABLE A2.2
49	TABLE A2.3
50	TABLE A2.4
51	TABLE A2.5
52	TABLE A2.6
54	TABLE A2.7
56	TABLE A2.8
57	X1. COIL AS A SOURCE OF STRUCTURAL PRODUCTS X1.1
58	X2. VARIATION OF TENSILE PROPERTIES IN PLATES AND SHAPES X2.1 X2.2 X2.3 X2.4 X2.5 X3. WELDABILITY OF STEEL X3.1 X3.2 X3.3 X3.4
59	X3.5 X3.6 X4. RADIUS FOR COLD BENDING X4.1 X4.2 X4.3 TABLE X4.1 TABLE X4.2

Additional information

Standard Title	A6/A6M-05e1 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
Published Code	ASTM
Publication Date	2005
Pages Count	61
ICS Codes	77.140.60 - Steel bars and rods