ASTM-A623 2008

$58.50

A623-08 Standard Specification for Tin Mill Products, General Requirements

Published By	Publication Date	Number of Pages
ASTM	2008	38

Guaranteed Safe Checkout

Categories: 77.140.50 - Flat steel products and semi-products, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products.

1.2 In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named.

Note 1A complete metric companion to Specification A 623 has been developed Specification A 623M; therefore no metric equivalents are presented in this specification.

1.3 The following safety caveat pertains to Annex A3 through Annex A10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology
2	TABLE 1
3	Base Metal Chemical Composition Cast or Heat Analysis Product Analysis Mechanical Requirements TABLE 2 TABLE 3
4	Permissible Variation in Dimensions TABLE 4 TABLE 5 TABLE 6 TABLE 7
5	Special Requirements Sheet Count—Cut Sizes Retest Procedure Conditions of Manufacture Inspection Rejection Packaging
6	Marking Keywords A1. ABBREVIATED RATIO TABLES FOR TIN MILL PRODUCTS A1.1 A1.2
7	TABLE A1.1
11	TABLE A1.2
12	TABLE A1.3
13	TABLE A1.4
17	TABLE A1.5
18	TABLE A1.6 TABLE A1.7 A2. ROCKWELL HARDNESS TESTING OF TIN MILL PRODUCTS A2.1 Scope A2.2 Anvil A2.3 Specimens
19	A2.4 Reports TABLE A2.1
20	A3. METHOD FOR DETERMINATION OF PICKLE LAG ON STEEL FOR ELECTROLYTIC TIN PLATE A3.1 Scope A3.2 Summary of Method A3.3 Apparatus A3.4 Reagents and Materials A3.5 Test Specimen Preparation
21	A3.6 Procedure A3.7 Calculation A3.8 Interferences A3.9 Assembly and Preparation of Apparatus FIG. A3.1
22	A4. METHODS FOR TIN CRYSTAL SIZE TEST FOR ELECTROLYTIC TIN PLATE A4.1 Scope A4.2 Summary of Methods A4.3 Apparatus (Required Only for Method No. 3) A4.4 Reagents and Materials (Required Only for Method No. 1) A4.5 Test Specimen A4.6 Procedure
23	A5. METHOD FOR DETERMINATION OF IRON SOLUTION VALUE ON ELECTROLYTIC TIN PLATE A5.1 Scope A5.2 Summary of Method A5.3 Apparatus A5.4 Reagents and Materials A5.5 Procedure
24	A5.6 Calibration A5.7 Calculation A5.8 Interferences A5.9 Precision
25	A6. METHOD FOR ALLOY-TIN COUPLE TEST FOR ELECTROLYTIC TIN PLATE A6.1 Scope A6.2 Summary of Method A6.3 Apparatus FIG. A5.1
26	A6.4 Reagents and Materials FIG. A6.1
27	A6.5 Test Specimen A6.7 Procedure FIG. A6.2
28	A6.8 Calculations A6.9 Hazards
29	A7. METHODS FOR DETERMINATION OF TOTAL SURFACE OIL ON TIN MILL PRODUCTS A7.1 Scope A7.2 Significance and Use A7.3 Summary of Method A7.4 Apparatus A7.5 Reagents and Materials A7.6 Hazards A7.7 Test Specimen A7.8 Preparation of Apparatus A7.9 Procedure A7.10 Calculations A7.11 Precision and Bias A7.12 Scope A7.13 Summary of Method A7.14 Apparatus
30	A7.15 Reagents and Materials A7.16 Hazards A7.17 Preparation of Apparatus A7.18 Procedure A7.19 Precision and Bias
31	A8. DETERMINATION OF CHROMIUM ON TIN PLATE BY THE DIPHENYLCARBAZIDE METHOD A8.1 Scope A8.2 Reagents and Materials A8.3 Procedure A8.4 Calibration of Spectrophotometer A8.5 Calculation of Chromium on Tin Plate
32	A9. METHOD FOR AERATED MEDIA POLARIZATION TEST FOR ELECTROLYTIC TIN PLATE A9.1 Scope A9.2 Summary of Method A9.3 Apparatus A9.4 Reagents and Materials FIG. A9.1
33	A9.5 Test Media A9.6 Test Specimen A9.7 Sample Preparation FIG. A9.2
34	A9.8 Aerated Media Polarization Test A9.9 Interpretation of Results
35	A10. DETERMINATION OF CHROMIUM ON TIN PLATE USING ATOMIC ABSORPTION A10.1 Scope A10.2 Summary of Test Method A10.3 Reagents and Materials A10.4 Apparatus A10.5 Procedure A10.6 Calculation FIG. A9.3
36	A11. METHOD FOR DETERMINING DRAWING TENDENCIES OF TIN MILL PRODUCTS USING A MODUL-R DEVICE A11.1 Scope A11.2 Terminology A11.3 Summary of Method A11.4 Apparatus A11.5 Sample Preparation A11.6 Procedure
37	FIG. A11.1
38	A11.7 Precision A11.8 Keywords

Additional information

Standard Title	A623-08 Standard Specification for Tin Mill Products, General Requirements
Published Code	ASTM
Publication Date	2008
Pages Count	38
ICS Codes	77.140.50 - Flat steel products and semi-products

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-A623 2008

PDF Catalog

Related products