BS EN 1559-2:2014
$142.49
Founding. Technical conditions of delivery – Additional requirements for steel castings
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 28 |
This part of EN 1559 specifies the additional technical delivery conditions for steel castings unless other conditions have been agreed at the time of enquiry and order.
This European Standard is also applicable to nickel and cobalt alloy castings.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | Contents Page |
| 5 | Foreword |
| 6 | Introduction |
| 7 | 1 Scope 2 Normative references |
| 8 | 3 Terms and definitions |
| 10 | 4 Information to be supplied by the purchaser 4.1 • Mandatory information 4.2 •• Optional information 4.3 ■ Drawings, patterns and tools 4.4 ■ Information on the mass 4.5 ■ Preliminary sample 4.6 ■ Initial sample 5 Designations 6 Manufacture 6.1 Manufacturing process 6.1.1 Melting 6.1.2 •• Heat treatment 6.2 Welding operations 6.2.1 ■ General 6.2.2 ■ Production welding 6.2.2.1 ■ 6.2.2.2 ■ |
| 11 | 6.2.2.3 ■ 6.2.2.4 ■ 6.2.2.5 ■ 6.2.2.6 ■ 6.2.2.7 •• Criteria for excavation 6.3 Further processing 7 Requirements 7.1 ■ General 7.2 Material 7.2.1 Chemical composition |
| 12 | Table 1 — Permissible deviations above the maximum or below the minimum limits of the chemical requirements of the applicable product specification for the results of product analysis 7.2.2 Mechanical properties 7.2.3 ■ Other properties |
| 13 | 7.3 Casting 7.3.1 ■ Chemical composition 7.3.2 ■ Mechanical properties 7.3.3 Outer and inner conditions (non-destructive testing) Table 2 — Testing methods 7.3.3.1 •• |
| 14 | 7.3.3.2 ■ 7.3.3.3 ■ 7.3.3.4 7.3.4 ■ Conditions of the casting 7.3.4.1 |
| 15 | 7.3.5 •• Mass of the casting 7.3.6 •• Additional requirements regarding the condition of the casting |
| 16 | 8 Inspection 8.1 ■General 8.2 ■ Type of inspection documents and type of inspection 8.3 ■ Test unit 8.3.1 •• Formation of test units 8.3.2 •• Size of test units 8.3.3 ■ Inspection frequency 8.4 Samples |
| 17 | Figure 1 — Sampling condition of test pieces in a t x 3t x 3t test block |
| 18 | 8.5 Test procedures 8.5.1 Test method and equipment |
| 19 | 8.5.2 ■ Rounding of results of mechanical and chemical tests 8.6 ■ Invalidation of test results 8.7 Retests 8.7.1 ■ General 8.7.2 Non-sequential tests (individual values) 8.7.3 Sequential tests 8.7.4 Special conditions |
| 20 | 8.8 ■ Sorting and reprocessing 9 Marking 10 ■ Packaging and surface protection 11 ■ Complaints |
| 21 | Annex A (informative) Mandatory and/or optional information checklist Table A.1 — Checklist |
| 25 | Annex B (informative) Significant technical changes between this European Standard and the previous edition Table B.1 — Significant technical changes between this European Standard and the previous edition |
| 26 | Bibliography |
