This part of ISO 13765 describes a method of determination of the flexural bonding strength of the bonded face between refractory bricks laid with refractory mortars (after drying and firing).<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 3<\/td>\n | TitlePage – Refractory mortars\ufffd\u2014 <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Foreword – Foreword <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Scope – 1\ufffd\ufffd\ufffd Scope NormativeReference – 2\ufffd\ufffd\ufffd Normative references Clause1 – 4\ufffd\ufffd\ufffd Principle Clause1 – 5\ufffd\ufffd\ufffd Apparatus UntitledSubclause2 – 5.1\ufffd\ufffd\ufffd Loading device UntitledSubclause2 – 5.2\ufffd\ufffd\ufffd Mixer <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | UntitledSubclause2 – 5.3\ufffd\ufffd\ufffd Electrical drying oven UntitledSubclause2 – 5.4\ufffd\ufffd\ufffd Consistency determining device UntitledSubclause2 – 5.5\ufffd\ufffd\ufffd Balance UntitledSubclause2 – 5.6\ufffd\ufffd\ufffd Callipers UntitledSubclause2 – 5.7\ufffd\ufffd\ufffd Furnace UntitledSubclause2 – 5.8\ufffd\ufffd\ufffd Thermocouple pyrometer <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | UntitledSubclause2 – 5.9\ufffd\ufffd\ufffd Cutting tool Clause1 – 6\ufffd\ufffd\ufffd Sampling and preparation of the test pieces Subclause2 – 6.1\ufffd\ufffd\ufffd Sampling Subclause2 – 6.2\ufffd\ufffd\ufffd Preparation of the test pieces Clause1 – 7\ufffd\ufffd\ufffd Procedure Subclause2 – 7.1\ufffd\ufffd\ufffd Preparation of the test specimens UntitledSubclause3 – 7.1.1\ufffd\ufffd\ufffd For dry mortars, take UntitledSubclause3 – 7.1.2\ufffd\ufffd\ufffd Take a pair of dried test pieces and apply a layer of the well-mixe… <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | Subclause2 – 7.2\ufffd\ufffd\ufffd Drying the test specimens Subclause2 – 7.3\ufffd\ufffd\ufffd Firing the test specimens Subclause2 – 7.4\ufffd\ufffd\ufffd Determination of flexural bonding strength UntitledSubclause3 – 7.4.1\ufffd\ufffd\ufffd Measure the width, UntitledSubclause3 – 7.4.2\ufffd\ufffd\ufffd Place a specimen on the bearing edges. Align the loading edge with … <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | UntitledSubclause3 – 7.4.3\ufffd\ufffd\ufffd Inspect the specimens one by one with care. If the area of voids in… Clause1 – 8\ufffd\ufffd\ufffd Calculation Clause1 – 9\ufffd\ufffd\ufffd Test report <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Refractory mortars – Determination of flexural bonding strength<\/b><\/p>\n |