IEC 62005-9-1:2015 establishes a general reliability qualification program that applies to all passive fibre optic components except connectors and connector assemblies, the passing of which, suggests a minimum level of reliability assurance and allows that specific device to be called qualified to this standard. The objectives of this International Standard are as follows: – to specify the requirements for a general reliability qualification standard (RQS) for passive optical components; – to give direction to the supplier and to the end user on the production and purchase of passive optical components to meet and verify reliability qualification standards for certain specified service environments; – to give the minimum list of reliability qualification stress tests and conditions; – to establish guidance for the selection of appropriate measurements and pass\/fail criteria; – to give relevant references; – and to establish the minimum reporting requirements. This standard defines a series of stress tests, their severity, sequences, quantities of devices under the test (DUT), acceptance criteria, and reporting requirements. It also gives guidelines to selecting appropriate measurements and pass\/fail criteria. Keywords: reliability qualification standard (RQS) for passive optical components<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 4<\/td>\n | European foreword Endorsement notice <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Annex ZA (normative) Normative references to international publications with their corresponding European publications <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 1 Scope 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 3 Terms, definitions and abbreviations 3.1 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 3.2 Abbreviations 4 General requirements 4.1 DUT 4.2 Product family 4.3 Service environments <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 5 Tests 5.1 General 5.2 Quantity of the DUTs 5.3 Sequence 5.4 Acceptance criteria 5.5 Test methods Tables Table 1 \u2013 Service environments <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 5.6 Severity 6 Measurements 6.1 General 6.2 Measurements 6.3 Pass\/fail criteria 6.4 Measurement methods 6.5 Required leak rate and residual gas analysis measurements 7 Report <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Annex A (normative) Required reliability qualification tests for passive optical components used in category C, controlled environments Table A.1 \u2013 Required reliability qualification tests for passive optical componentsused in category C, controlled environments (1 of 2) <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Annex B (normative) Required reliability qualification tests for passive optical components used in category U, uncontrolled environments Table B.1 \u2013 Required reliability qualification tests for passive optical components usedin category U, uncontrolled environments <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Annex C (normative) Required reliability qualification tests for passive optical components used in category O, uncontrolled environments (sequential) Table C.1 \u2013 Required reliability qualification tests for passive optical componentsused in category O, uncontrolled environments (sequential) (1 of 2) <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | Annex D (informative) Informative and optional reliability qualification tests for passive optical components used in category C, category U and category O environments D.1 Informative and optional reliability qualification tests for passive optical components used in category C, controlled environments Table D.1 \u2013 Informative and optional reliability qualification tests for passive optical components used in category C, controlled environments (1 of 2) <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | D.2 Optional reliability qualification tests for passive optical components used in category U, uncontrolled environments D.3 Informative reliability qualification tests for passive optical components used in category O, uncontrolled environments (sequential) Table D.2 \u2013 Optional reliability qualification tests for passive optical components used in category U, uncontrolled environments <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | Table D.3 \u2013 Informative reliability qualification tests for passive optical components used in category O, uncontrolled environments (sequential) <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | Annex E (informative) Failure mode and known failure mechanisms for passive optical components Table E.1 \u2013 Failure mode and known failure mechanisms for passive optical components (1 of 20) <\/td>\n<\/tr>\n | ||||||
| 47<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Fibre optic interconnecting devices and passive components. Reliability – Qualification of passive optical components<\/b><\/p>\n |